|
|
Digitizer/Planimeter - Model 1280
click to enlarge
This is the best planimeter for digitizing recorder paper
graph charts, maps, drawings and photographs. The planimeter
directly measures area and length for X-Y coordinates and
imports them into the computer database software.
Measuring results of areas and lengths can be independently
accumulated. The two large 8 digit 1/2" display panels can be
assigned to show areas/lengths in different measuring units,
counts, or X/Y coordinates.
The cursor is equipped with 12 dual function keys and a
programmable handle switch that can be assigned to control any
of the major functions. It has extremely low friction and
momentum for minimum operator fatigue.
A separate keypad (standard) is used to enter scale ratios,
define coordinates, establish the X-axis etc. It also serves
as a remote data entry keypad for the host computer.
The RS232 interface works via the serial port of virtually
all computers and can emulate most popular tablets for work
with CAD Software (AutoCad, etc.). Also supplied is a resident
DOS Driver which transmits data from the digitizer to many
commercial programs including Lotus 1-2-3.
310-030 Model 1280 Digitizer/Planimeter 12 lbs.
Sokkia™ Tamaya Digital Planimeters
Digital Planimeters are precise instruments for fast,
accurate determination of areas from blueprints, maps, photos,
etc. Following the outline of the area with the tracer, the
revolution of the measuring wheel in either direction is
sensed by the electro-shaft encoder, and the corresponding
data is digitally displayed.
Planix 5 and Planix 6
 |
 |
| Planix 5 |
Planix 6 |
Readings in square inches or square centimeters. Planix, 5,
the Polar Compensation Type and Planix 6, the Linear (Roller)
Type, feature zero-setting, metric or English convertible
scale and accumulative measurement function, 8 digit LCD
readout. Compact, cordless operation for 30 hours - with
rechargeable NiCd battery (15 hour charging time) and power
saving automatic power turnoff after left unused for 3
minutes. Averages multiple measurements and has display hold
button to prevent inadvertent loss of measurements. The polar
arm length of the Planix 5 is 8.88".
Each Planix is supplied with battery, AC adapter, battery
charger and a hard molded carrying case with foam inserts.
310-035 Planix 5 52.5 lbs.
310-036 Planix 6 62 lbs.
310-037 Replacement Battery 0.3 lb.
Planix 7 and Planix 8
 |
 |
| Planix 7 |
Planix 8 |
User entered map scale factors to obtain direct readings in
any desired unit. The Planix 7, linear-roller type and Planix
8, polar compensation type, feature the same functions as the
Planix 5 and Planix 6 with several additional features.
Both models display the measured area direction in terms of
cm, m, km, in., to ft. or acres depending on selection, with
both the X and Y scales entered by the user. The display will
automatically shift to the next largest unit if the selected
unit has overflowed its capacity, i.e. from in. to ft.. Back
up memory for scale factors are stored when power switch is
turned off. The polar arm length of the Planix 8 is 9".
Each Planix is supplied with NiCd battery, AC adapter,
batter charger and a hard molded carrying case with foam
inserts.
310-040 Planix 7 71.5 lbs.
310-041 Planix 8 81.5 lbs.
Super Planix β
click to enlarge
The Super Planix β can simultaneously obtain area, line
lengths, side lengths and coordinates with a single tracing.
Area and line lengths of complex diagrams are found by point
mode measurement by plotting points on straight lines or
stream mode for tracing curves on curved lines.
Special features make the Super Planix β easier to use than
other planimeters. The point coordinate/stream tracing button
is located on the tracer lens and the entire tracing arm
rotates in either direction for operation by right and left
handed users. Obtain averages and total several measurements
with only three keys and also features on-board memory and
measurement recall buttons. The following units are standard:
mm, cm, m, km, hectares, in., ft., sq . ft., yd., miles and
acres. Other units can be entered using the calculator
function. Designed with an RS-232 interface for connection
with a computer. An optional thermal printer is available for
a permanent record of important computations. RS-232 interface
cable sold separately.
310-045 Super Planix
β 2.5 lbs.
310-047 Optional Thermal Printer 1 lb.
310-048 RS-232 Interface Cable 2 lbs.
top
|
