Water Level
Meter - Model 1010
Flat Tape Water Level Meter
This electric contact gage is used for measuring
the depth of water in wells, boreholes, standpipes
and bridge tapedows during discharge measurements.
The Flat Tape Water Level Meter is reliable,
accurate and easy to operate and read to 1/100 ft.
or mm.
The Model 1010 Water Level Meter uses a
well-designed probe, attached to a permanently
marked polyethylene tape, fitted on a well-balanced
reel. The conductors embedded within the tape each
have seven strands of stainless steel.
The probe incorporates an insulating gap between
electrodes. When contact is made with water, the
circuit is completed, sending a signal back to the
reel. This activates a loud buzzer, and a light.
Features:
Accurate
- markings each 1/100 ft., 1/2", cm or mm
- sensitivity adjustable to conductivity
- shielded probes to avoid false readings
- lengths up to 3000 ft. (900 m)
Reliable
- permanent, hot stamped markings
- stranded stainless steel conductors
- rugged, free standing reel
- standard 9V battery
The
design of the tape prevents it from adhering to wet
surfaces in boreholes and wells. Markings are
permanently embossed onto one side of the tape and
are available in your choice of scales. The tape can
also be printed on both sides. English graduations
are in feet, 10ths and 100ths. Metric graduations in
meters, decimeters, centimeters and millimeters.
All sizes of reel are free-standing, robust and
run smoothly. Each is equipped with a convenient
carrying handle. On the faceplate of each reel there
is an on/off/sensitivity switch, light, battery test
button, and a winding handle. The battery is housed
in the hub of the reel, and on the back is a probe
holder and the brake. A carrying bag is available
and sold separately.
All probes are designed to reduce or eliminate
problems with cascading water. The following options
are available:
- P2 Stainless Steel: with a neoprene strain
relief. 0.5" dia. by 7.5" long (12.7 mm x 190 mm)
- P3 Narrow Diameter: stainless steel probe 0.4"
dia. by 4.75" long (10.2 mm x 120mm)
- P4 Environmental: stainless steel. Design
permits submergence below water. Gives improved
operation in both cascading water and low
conductivity water. The probe pulls apart for easy
cleaning and decontamination and to accept T4
Sleeve. 0.625" dia by 8.625" (15.9mm x 220mm)
- T4 Temperature Sleeve: for P4 probe allows
profiling of temperature in wells. Sleeve
enclosing a thermistor slips over the P4 probe
body. 0.625" dia. by 8.75" (15.9mm x 222 mm).
Accuracy: ±1° C. Range: -5° C to +50° C.
807-001 30 ft/ 10 M
Level Meter 4 lbs.
807-002 65 ft/ 20 M
Level Meter 5 lbs.
807-003 100 ft/ 30 M
Level Meter 6 lbs.
807-004 150 ft/ 50 M
Level Meter 7 lbs.
807-005 200 ft/ 60 M
Level Meter 7.5 lbs.
807-006 300 ft/ 100 M
Level Meter 8 lbs.
807-007 500 ft/ 150 M
Level Meter 15 lbs.
807-008 Carrying Case
3 lbs.
Coaxial Cable Water Level Meter - Model 1020
This Coaxial Cable Model is accurate, reliable
and easy to use. The coaxial style is preferred if
using for bridge tape downs for stage reference
checks during discharge measurements because coaxial
is more wind resistant and less likely to "bow" in
the wind giving more accurate measurements. It has
selectable audible buzzer or visual ultra-bright LED
indication. Thin 3/8 in. probe sensor allows easy
access even through a 1/2" bolt hole and has a
variable sensitivity switch for signal accuracy in
different water and well conditions. Strong,
lightweight coaxial cable 1/10" dia. and is
permanently marked in 100ths of a foot or
millimeters. Probe is highly sensitive, yet
unaffected by cascading water. Completely
self-contained, it requires no external power or
ground and uses one 9V battery.
807-020 100 ft./ 30 M
Level Meter 6 lbs.
807-021 150 ft./ 50 M
Level Meter 7 lbs.
807-022 300 ft./ 100 M
Level Meter 8 lbs.
807-023 500 ft./ 150 M
Level Meter 15 lbs.
Kolor Kut Gaging
Paste
This is an economical method of determining water
levels and this unique paste can be used with a
measuring tape, rod or calibrated line to determine
water level. Apply the paste in the area that the
level is expected to appear. When the paste comes in
contact with water it will immediately change from
golden brown to bright red, marking the level. After
use, the paste can easily be wiped off with no
residue.
807-030 3 oz. Tube
Water Finding Paste
0.5 lb.
Top
